HR32210J Industrial Relay Module: Comprehensive Guide for PLC Automation Systems

February 17, 2026

Historical parts record: Photos and notes below belong to this record. Confirm the offered unit’s full model, condition and available test evidence before ordering.

What this delivery is: ten NSK HR32210J single-row tapered roller bearings — genuine NSK, JAPAN etched on every set of rings — brand new in their original boxes, ten pieces to the order, received 2025-11-04. The listing title that came with this article says relay module, and that is simply wrong: the photographs show bearings, not relays, and the article is written from the bearings themselves. Every ring carries the maker's etching — NSK, JAPAN and HR 32210J — and every box is the NSK Motion & Control purple label printing HR 32210J with the 24-10 batch code.

Reading the bearing

The 32210 is a metric single-row tapered roller bearing in the ISO 322 series: 50 mm bore, 90 mm outside diameter, 24.75 mm overall width — a medium-duty tapered section that takes combined radial and one-direction thrust loads, the reason it ends up in wheel hubs, gearboxes and machine-tool spindle supports. The HR prefix is NSK's designation for its standard-ground tapered series, and the J suffix is the standard tolerance class. Like all single-row tapereds, it must run opposed to another tapered bearing (or be preloaded by its shoulder) so the axial play is set by the shim or nut on assembly rather than by the bearing itself. The rings arrive in NSK's clear service bags inside the boxes; the rollers ride their pressed steel cages with the factory rust preventive in place.

Item	Detail
Product	NSK HR32210J single-row tapered roller bearing, standard class (J)
Boundary dimensions	50 mm bore × 90 mm OD, 24.75 mm overall width (ISO 322 series)
Ring etching	NSK / JAPAN / HR 32210J on the outer-ring face
Box label	HR 32210J, 24-10 batch code, NSK Motion & Control purple label — all ten boxes one marking
Loading note	Single-row tapered: mount opposed with controlled axial preload; not a float bearing on its own
Condition / quantity / weight	New in original boxes; 10 pcs; 7 kg total per record; received 2025-11-04

Fitting notes

Two assembly points decide how a 32210 behaves in service. First, preload: the opposed pair is set by measuring end float and shimming until the spec calls for it — a tapered set run with too much float walks and brinells, one run too tight cooks its lubricant. Second, cleanliness at the moment of fitting: the rings are ground to microns, and a fingerprint left on the raceway during a hot mounting becomes a mark for life. Warm the inner ring (induction heater, never a flame) for a shrink fit onto the shaft, seat against the shoulder square, and lock the adjustment nut to the torque the housing drawing gives. The ten units here are one batch — one 24-10 code — so a set split across two positions of the same assembly shares the same manufacturing run. Other Japanese-bearing records from this series: the SKF 7209 BECBP angular contact and the SKF 6312-2RS1/C3 deep groove.

Photos

Bearing in service bag — The first bearing as it comes out of the box: rings and roller set in NSK's clear service bag, the tapered geometry readable through the film.

Ring face in bag — The ring face through the bag: the ground bevel and the edge of the etched marking on a second unit.

Ten NSK boxes — All ten boxes as delivered: the NSK Motion & Control purple label on each, HR 32210J with the 24-10 batch code printed on the sides — ten of one part, one batch.

NSK box lids — The box lids: NSK BEARINGS and NSK Ltd. MADE IN JAPAN over the purple ground — the outer faces that identify the maker before any box is opened.

Ring etching close-up — The etching in close-up through the bag: HR 32210J cut into the ring face — the type called out where a fitter checks it.

Full bearing with three etchings — The whole bearing face-on: NSK at one side, JAPAN at the other, HR 32210J below — the three etchings that settle authenticity in one frame.

Box labels stacked — The box labels in close: HR 32210J / 24-10 repeated down the stack, red NSK Motion & Control blocks below — consistent printing across the set.

Rollers and cage — Rollers and pressed-steel cage through the bag film: the tapered roller line and its separator, factory grease still on the surfaces.

Second unit etchings — A second unit for the portrait: NSK, JAPAN and HR 32210J again on the ring face — the etching consistent unit to unit.

Third unit in bag — The third bagged set: rings and cage square-on, film sealed — the condition every one of the ten arrived in.

Related products on KOEED

Related reads from this series: the SKF 7209 BECBP angular contact bearing and the SKF 6312-2RS1/C3 deep groove bearing.

Need NSK HR32210J from this batch of ten, another 322-series size, or a preload spec for your housing? Send the bearing number — we confirm stock with photos.

Request a quote