Omron E5CN-HR2M-500 Temperature Controller: Advanced Industrial Automation Solution

January 12, 2026

Pre-shipment Inspection Record: This document details the visual and technical inspection of the Omron E5CN-HR2M-500 Temperature Controller: Advanced Industrial Automation Solution. All product photos and testing videos below are original materials captured first-hand by the Koeed technical team in our warehouse prior to dispatch.

What is the Omron E5CN-HR2M-500?

The E5CN-HR2M-500 is Omron's high-performance E5CN-H temperature controller in the 48 × 48 mm panel format: multi-range input across the standard thermocouples and PT100 platinum RTD, a 100-240 V AC supply, and the HR2M output build — relay control output with two alarm outputs (ALM1/ALM2, 3 A each) — on the 11-terminal rear block. The side label draws the full terminal map and carries the approvals (cULus Listed, CE); the factory cartons read TYPE E5CN-HR2M-500, TEMP CONTROLLER, MULTI-RANGE, 100 to 240 V/AC, MADE IN JAPAN. This record is two units, each in its factory carton with its own lot code (2681MR and 26811MR), new as photographed. Note on the source photo set: two frames of unrelated power-module photos were filed with this record; they are excluded from this page and the count here follows the controller photos only — the intake record books one unit, the photo set shows two, and both are stated. All 9 photos and 1 video below show these exact controllers.

3 min readContent reviewed 8 October 2026

Part details

E5CN-HR2M-500, as printed on the carton and side label
Field	Value
Model	Omron E5CN-HR2M-500
Type	High-performance digital temperature controller, 48 × 48 mm (E5CN-H)
Input	MULTI-RANGE — TC / PT100 platinum RTD (operation menu: PT100, −200 to 850 °C class ranges)
Supply	100 to 240 V AC, 50/60 Hz, 8.7 VA
Outputs	OUT1 relay 3 A / 250 VAC; ALM1 / ALM2 relay 3 A / 250 VAC (side label)
Display / controls	PV/SV double display; four-key front (parameter, mode, down, up)
Approvals	cULus Listed (Process Control Equipment), CE — side label
Lots	2681MR and 26811MR — one factory carton each; serial barcode (01)04547648452717 (21)268447481
Origin	Made in Japan — OMRON Corporation
Quantity	2 units in factory cartons shown; intake record books one — both as recorded

Scroll sideways to see the full table.

Values are read from the factory cartons, the side wiring labels and the photographed construction in the photo set.

The E5CN-H tier, and what HR2M wires

The E5CN-H is the performance tier of Omron's 48 mm controller line — faster sampling, auto-tuning that holds tight process bands, and the multi-range input that lets one part number serve every thermocouple and PT100 loop on the floor. The suffix decides the wiring, and HR2M reads plainly: R for the relay control output, 2 for the two alarm outputs, M for the multi-range input — a controller that switches a heater bank directly at 3 A, raises over-temperature and deviation alarms independently, and accepts whatever sensor the loop already runs. The side label carries the terminal map in full — control output and alarms across 11-15, the input on 1-5, the 100-240 V supply at 8.7 VA — printed where the wiring lands, which is how these controllers keep their commissioning time short. The operation menu shipped with the units lists the input table (PT100 platinum resistance from −200 °C through 850/500/2100 °C ranges), the reference for setting the input type to match the sensor in the loop. Two factory cartons with distinct lot codes are photographed here — one replacement now, one for the shelf — with the intake record's single-unit count noted alongside.