Mitsubishi G170EG01 Industrial HMI Display Panel: Complete Technical Guide

16. januar 2026

Historical parts record: Photos and notes below belong to this record. Confirm the offered unit’s full model, condition and available test evidence before ordering.

What is the G170EG01 LCD panel?

The G170EG01 is AU Optronics' 17-inch SXGA industrial TFT panel — 1280 × 1024 resolution, CCFL backlight, metal frame — the display cell that Mitsubishi and other HMI builders fitted to their operator terminals. One correction to this listing's title: the panel is AU Optronics hardware, not Mitsubishi-branded — Mitsubishi was the equipment maker whose terminals used it. The rear labels read the identity: Manufactured 12/41 (2012, week 41), Model No: G170EG01 V.0, 01XXG, AU Optronics, MADE IN CHINA (S1), cRUus E204356, RoHS Pb-free, with barcodes AU170280CCTC9SZ222AE07P6 and F15917G020012A90001042B093904. One unit, tested pull at near-new condition ("可以充新" as recorded — cleaned and graded to recharge-new), one-year warranty as recorded at intake on 29 November 2025. All sixteen photos and the inspection video show this exact panel.

3 min readContent reviewed 8 October 2026

Part details

G170EG01 V.0, as read from the rear labels and the construction
Field	Value
Brand	AU Optronics — MADE IN CHINA (S1 plant), manufactured 2012 week 41
Model	G170EG01 V.0, 01XXG — 17.0-inch SXGA industrial TFT
Resolution	1280 (RGB) × 1024 (per intake record, the SXGA class)
Backlight	CCFL, two lamp sets with white plug connectors taped to the rear; mercury disposal note on the label (cold-cathode lamp)
Signal	LVDS connector along the bottom edge
Construction	Aluminium front bezel over a stamped rear shield with ventilation slots; label row: 72238334DJZZ-ZS0101, AU170280CCTC9SZ222AE07P6, F15917G020012A90001042B093904 (LGP>PMMA, Frame>PC-GF10FR)
Markings	cRUus E204356, RoHS, 15 recycling, QC PASS 06 sticker; workshop YD dated sticker
Condition	Tested pull graded near-new (可以充新), 1-year warranty, intake 29 November 2025

Scroll sideways to see the full table.

Values are read from the rear labels and the photographed construction in the photo set.

Swapping the panel behind a terminal

When an industrial HMI's picture dims, yellows or dies, the fix is the panel cell behind the bezel — and the G170EG01 is that cell for a generation of Mitsubishi and similar terminals. The swap is a connector-for-connector job: the LVDS ribbon lands on the same socket, the two CCFL lamp leads plug into the inverter the machine already has, and the metal frame bolts into the bezel the old panel left behind. Because the G170EG01 was the fitment across a terminal family, its replacement panel carries the machine's original resolution and brightness characteristics — no driver changes, no scaling surprises.

This unit is a tested pull graded to near-new — the intake's 可以充新 (recharge-new) grade, meaning cleaned, verified and photographed as the cosmetic equal of a new part. The rear labels are all legible: the AU Optronics manufacture line with the 2012-week-41 date, the cRUus file number, the two trace barcodes, and the lamp-materials disposal note that a cold-cathode panel carries. For a terminal whose display has failed, this is the exact-fit cell — and the photos document every label and connector so the fitment check happens before purchase.

Photos

All images below are original KOEED warehouse photos. Click any photo to view it full size.

Panel front in box — The panel front in its box: the dark polariser under its protective film, the aluminium bezel and the mounting holes at the corners.

Rear full — The rear in full: the stamped shield with its ventilation slots, both CCFL leads taped flat, the label row and the QC PASS 06 sticker.

Labels square — The labels square-on: Manufactured 12/41, Model No: G170EG01 V.0, AU Optronics, MADE IN CHINA (S1), cRUus E204356, RoHS — with the AU170280CCTC9SZ222AE07P6 barcode and the lamp-materials disposal note.

Labels angled — The labels at an angle with the CCFL leads above: F15917G020012A90001042B093904, LGP>PMMA, Frame>PC-GF10FR — the materials marking of the light guide and frame.

Panel side in box — The panel on edge in its box: the frame depth and the top bracket — the mechanical fit the terminal bezel expects.

Rear full second — The rear from the second angle: both taped leads, the label row and the QC sticker — the panel as received.

Side edge — The side edge: the frame stampings — the side stamp code and the 120909 date beside the corner bracket.

The CCFL connectors: the white plug pairs on their lead sets — the backlight connections to the inverter.

Bezel corner — The bezel corner: the aluminium profile, the screw holes and the film edge — the finish side of the swap.

The LVDS socket close-up: the connector along the bottom edge — the signal side that carries the picture in.

YD sticker — The workshop sticker: the YD mark dated 202-1-28 — the intake inspection note beside the LVDS edge.

Labels close second — The labels at a second close angle: the AU170280 trace barcode and the materials line — readable for the parts book.

On edge top bracket — On edge from the top: the bracket, the CCFL lead routing and the shield screws — the install side.

Front polariser — The front polariser with its film: clean and uniform — the near-new grade the intake graded it to.

The CCFL plug close-up: the white housing pairs with their lead colours — wired as the inverter expects.

Final angle — The final angle: labels, leads and shield — the panel as it goes on the shelf.

Inspection video, recorded at the Koeed warehouse before dispatch.

For the driver-board side of the display family from the same warehouse, see the EW60111BMW LCD module — the driver-integrated display unit, documented the same way.