2025/10/13 859-304, Sales records with pictures and video

24 octobre 2025

Historical parts record: Photos and notes below belong to this record. Confirm the offered unit’s full model, condition and available test evidence before ordering.

What is the WAGO 859-304 relay module?

The 859-304 is a WAGO DIN-rail relay module: feed 24 V DC / 12 mA into the coil terminals (A1+ / A2−) and it switches a single changeover contact — terminal 11 common, 12 normally-closed, 14 normally-open — rated 250 V AC / 5 A / 50–60 Hz. Inside the grey housing sits a WAGO 857-152 relay (6 A / 250 V~ contacts, cULus recognised) on a 636-288 V04 board with a red status LED, and the module carries the full certification row on its face: CE, UKCA, CCC, EAC, cULus Listed E175199 (AC230V/6A), and ATEX/IECEx/UKEX/CCC-Ex II 3G Ex ec nC IIC T4 Gc for Zone 2 panels (WAGO16ATEX9000X). Terminals are push-in spring clamp, taking 0.08–2.5 mm² (AWG 28–14) stripped 5–6 mm; ambient −40 °C to 50 °C. This record covers a full factory box of ten, batch 10044840922323---04, made in WAGO's P. R. China plant (box date 0720), received new in original packaging with a three-month warranty; they passed through the Koeed warehouse on 13 October 2025, and the nine photos below show them as received.

3 min readContent reviewed 6 October 2026

Part details

WAGO 859-304 relay module, per module face and box labels
Field	Value
Manufacturer	WAGO (Hansastr. 27, D-32423 Minden); made in P. R. China, box code 0720
Part number	859-304, relay module (REL / 继电器模块); box ID 60341831
Input	=24 V DC / 12 mA at A1+ / A2− (polarity marked, rectifier-plus-LED coil circuit)
Output contact	SPDT — 11 common, 12 NC, 14 NO; 250 V AC / 5 A / 50…60 Hz (cULus file E175199 lists AC230V/6A)
Built-in relay	WAGO 857-152, 24 V= coil, 6 A / 250 V~ and 6 A / 277 V~ contacts, cULus; PCB 636-288 V04, red LED indicator
Terminals	Push-in spring clamp, 0.08–2.50 mm² / AWG 28–14, strip 5–6 mm
Ambient	−40 °C ≤ Tamb ≤ 50 °C
Certification	CE, UKCA, CCC, EAC, cULus Listed E175199; Ex II 3G Ex ec nC IIC T4 Gc — WAGO16ATEX9000X, UKEX WAGO22UKEX007X, CCC 2021312304000982
Batch / quantity	10044840922323---04, 10 modules per factory box
Condition	New in original packaging (per intake record); three-month warranty
Intake recorded	13 October 2025

Scroll sideways to see the full table.

Reading the face and the box

The module face is a one-glance datasheet, printed in DIN notation: IN "=24V / 12mA" — the equals sign means direct current — and OUT "~250V / 5A / 50…60Hz", where the tilde marks alternating current. The circuit diagram beside it shows the coil with its suppression diode and LED, and the terminal legends map the wiring: A1+/A2− for the coil, 11/12/14 for the changeover contact. The box repeats the order data — 10 × 859-304, REL, 继电器模块 (relay module), ID 60341831 — plus the wire range pictogram (0.08–2.50 mm², AWG 28–14, 5–6 mm strip) and the hazardous-location marks. Note the ATEX/ec nC rating: this is the Zone 2 (Category 3) variant, for use in areas where explosive gas is not present under normal operation.

Where it fits

This is the classic PLC-interface building block: a 24 V DC logic output drives the coil, and the relay contact switches a heavier AC load — a contactor coil, a lamp bank, a small motor starter signal — with the LED showing coil state at a glance. Because the module is one DIN-rail unit wide with push-in terminals, panels built from these snap together quickly, and the batch number on every unit in this box is identical (10044840922323---04), so the ten modules are one production run. Before installing, note the polarity on the coil terminals and keep within the −40…50 °C window; the contacts are rated for resistive loads at the printed values, so apply appropriate derating for inductive loads.

Photos

All images below are original warehouse photos of the exact modules covered by this record, taken before dispatch. Click any photo to view it full size.