Mitsubishi FX2N-4DA Analog Output Module: Complete Guide for Industrial Automation

24 styczeń 2026

Historical parts record: Photos and notes below belong to this record. Confirm the offered unit’s full model, condition and available test evidence before ordering.

The Mitsubishi FX2N-4DA is the four-channel analog output expansion for the FX2N PLC family — each channel sources −10 to +10 VDC or 0 to 20 mA, powered from 24 VDC, hanging off the right side of the CPU through the supplied ribbon cable. This unit is version 1.10, a 2024.09 certification batch (KC KCC-REI-MEK-09M114), still in current production at Mitsubishi's Japanese plant. New in the sealed factory carton, serial 2492608, received 2026-01-23, 1-year warranty.

What the nameplate says

Item	Value on nameplate
Model	FX2N-4DA
Power supply	24 VDC
Outputs	−10 ~ +10 VDC, 0 ~ 20 mA (4 channels)
Version	1.10
Certification batch	KCC-REI-MEK-09M114 2024.09
Category	80M1, IND. CONT. EQ.
Certifications	cULus US LISTED, CE, KC, EAC
Serial	2492608 (M/C 09M11424092432, G/C 09M114)
Origin	Made in Japan — Mitsubishi Electric Corporation, Tokyo

FX2N-4DA factory carton — Factory carton: Mitsubishi Electric Programmable Controller, FX2N-4DA, serial 2492608, M/C 09M11424092432, G/C 09M114, CE and KC marks (KCC-REI-MEK-09M114 2024.09), 原产地日本国合格证 sticker, QR code, MADE IN JAPAN.

FX2N-4DA nameplate — Module nameplate: model, 24VDC power, −10~+10VDC / 0~20mA output ranges, VERSION 1.10, 80M1 IND. CONT. EQ., cULus / KC / EAC / CE marks, SERIAL NO. 2492608.

Front and connections

FX2N-4DA front face — Front face: POWER LED up top, FX2N-4DA print, and the 24V / D/A status LEDs below. To the left sit the dust-proof sheet pack (JY993D45701F, films No.0–No.7) and the gray ribbon expansion cable; the blue ESD bag on the right holds the accessory set.

FX2N-4DA module with accessories — The module with its accessories laid out: carton behind, dust-proof sheet pack and gray ribbon cable on the left, sealed ESD bag on the right.

FX2N-4DA rear ribbon cable — From the rear: the 20-pin ribbon cable that daisy-chains to the CPU (or the module before it) is captive on the module side, PCB edge visible in the slot.

FX2N-4DA cable connector close-up — The ribbon connector end — gold contacts, keyed shroud, still protected by the factory strip.

Video: the module turned on the bench — nameplate, front face and rear in sequence.

Mounting face

FX2N-4DA DIN rail clip — Back side: the white DIN-rail release latches, screw-mount eyes top and bottom, the covered expansion slot, and the terminal block edge on the right.

Using the module

Four output channels share 12-bit resolution; voltage mode drives −10 to +10 V into a load of 2 kΩ to 1 MΩ, current mode sources 0–20 mA at up to 500 Ω. Buffers hold the output values, so the analog levels survive a PLC stop. Setup is the standard FX block transfer — write the channel enable word plus per-channel data and range codes from the CPU program. A DP (D/A power) LED faults with the 24 V supply, which is the first thing to check when outputs read zero.

Condition and delivery facts

New in the sealed carton with all accessories: dust-proof film set, ribbon cable fitted, documentation sheet. Received 2026-01-23, single unit, 1-year warranty.