GE Fanuc IC693ALG390 Series 90-30 Analog Output Module: Complete Technical Guide

18 de fevereiro de 2026

Historical parts record: Photos and notes below belong to this record. Confirm the offered unit’s full model, condition and available test evidence before ordering.

What this delivery is: a GE Fanuc IC693ALG390 analog output module — the Series 90-30 two-channel ±10 VDC voltage output card — brand new in original packaging with the factory information card, one-year warranty per the record, 1 kg, received 2026-02-07. This unit is the early joint-brand build: GE roundel beside the red FANUC block on the face label, and the rear nameplate closes with GEFanuc — the partnership era of the 90-30 line, made in Charlottesville, Va., USA, barcode A543562 0928.

Reading the module

The IC693ALG390 is the two-point voltage output of the 90-30 analog family: two channels, each swinging −10 to +10 VDC, with 5 mA of drive per point — enough for chart recorders, drive references and isolator inputs, not enough to run anything that needs real current. The terminal door labels it all in one strip: OUTPUT ANALOG VOLTAGE, CHANNEL 1, CHANNEL 2, and the rating line −10 to +10 VDC / 5mA/Pt. Behind the door each channel is a +/− pair; the module registers into the CPU's %AQ table in slot order, and the output updates on the backplane scan. The rear nameplate carries the hazardous-location set shared across this family: cULus Listed 8M89 E157515, Class I Div 2 Groups ABCD, EEx nA IIC T5 X, 0C to 60 °C ambient, T4A — the card is rated to sit in a Division 2 panel without extra enclosures. The box also carries the factory IMPORTANT PRODUCT card — the READ THIS sheet with the explosion-hazard wiring warnings and the NEC Article 501-4(b) reference that Division 2 installs work to.

Item	Value on the module / in the record
Product	GE Fanuc IC693ALG390, Series 90-30 analog output module
Outputs	2 × voltage channels, −10 to +10 VDC, 5 mA per point (door label)
Terminal door	OUTPUT ANALOG VOLTAGE; CHANNEL 1; CHANNEL 2; rating strip
Identification	GE + FANUC joint face label; rear barcode A543562 0928; hand mark P230
Certifications	cULus 8M89 E157515; Class I Div 2 Groups ABCD; EEx nA IIC T5 X; 0-60 °C; T4A; CE; GEFanuc
Included paper	Factory IMPORTANT PRODUCT card (explosion-hazard wiring warnings, Series 90-30 Products)
Origin	Made in Charlottesville, Va. USA
Condition / quantity / weight	New, genuine, 1-year warranty; 1 pc; 1 kg; received 2026-02-07

Fitment notes

This is the card for analog command signals: a speed reference to a VFD's −10/+10 input, a position setpoint to a servo drive, a ratio to a controller. Respect the 5 mA — buffer through an isolator or a signal repeater if the load draws more, because a loaded voltage output droops and the loop that depends on it drifts with it. The two channels share the module's ground; keep the output runs away from the AC wiring or use shielded pairs grounded at one end. Swaps are slot-for-slot, and a 90-30 CPU reads it back into %AQ with no reconfiguration when the slot is kept. The 90-30 records in this series now line up as a rack: the IC693ALG223D 16-point current input, this IC693ALG390 voltage output, and the IC693CMM321 communications module.

Photos

Terminal door with channel labels — The terminal door in close: OUTPUT ANALOG VOLTAGE over CHANNEL 1, CHANNEL 2 — the two output channels and their screws under the clear cover.

Rating strip on door — The rating strip at the door's foot: −10 to +10 VDC, 5mA/Pt — the voltage window and the 5 mA-per-point drive limit that sizes the load.

GE FANUC joint label — The face label: the GE roundel beside the red FANUC block — the joint-brand build — over IC693ALG390, barcode A543562, and the hand-marked P230.

Module side — The module in its static skin: black case, terminal edge and the rear connector line — sealed as delivered.

Full terminal face — The full terminal face: door label with both channels and the rating strip, module latches either side — the working end in one frame.

Rear cavity detail — The rear cavity: the internal ribbon, backplane pin row and the hand-marked D 409 figure on the shell.

The side profile through the bag: case latches, terminal row and the rear connector line.

Rear nameplate — The rear nameplate in full: IC693ALG390 / OUTPUT ANALOG / 2PT VOLTAGE, cULus LISTED 8M89 E157515, Ex II 3 G, CLASS I DIV 2 GROUPS ABCD, EEx nA IIC T5 X, T4A AMB 60C GEFanuc, A543562 0928, Made in Charlottesville, Va. USA.

Factory information card — The factory IMPORTANT PRODUCT card in the box: READ THIS — the explosion-hazard warnings and Class I Division 2 wiring requirements for the Series 90-30 products, original paper with the module.

Related products on KOEED

The same model on the storefront: GE FANUC IC693ALG390, plus the FANUC IC693ALG390 listing. Related reads: the IC693ALG223D input module and IC693CMM321 records.

Need the IC693ALG390 for your rack, another 90-30 analog card, or an output-buffering note for your loop? Send the slot plan — we confirm stock with photos.

Request a quote