Compatible Canon SX610 SX620 SX720 HS Digital Camera LCD Display Screen Parts ~

Canon Compatible · PowerShot SX Series · LCD Display · Screen Replacement · In stock

What Is the Compatible Canon SX610/SX620/SX720 LCD Display Screen?

This is a compatible replacement LCD display screen assembly for the Canon PowerShot SX610 HS, SX620 HS, and SX720 HS compact digital cameras. These three models share the same rear LCD panel form factor, resolution, and ribbon cable interface, making one replacement part compatible across the series. The screen is the 3.0-inch TFT LCD that serves as the camera's viewfinder, menu navigation display, and photo review screen — and it is also the most mechanically vulnerable component on the camera. A drop, a knock against a hard surface, or pressure in a bag can crack the LCD panel or damage the internal layers, rendering the camera unusable even though the lens, sensor, and electronics remain perfectly functional.

In short: The rear LCD screen panel for the Canon SX610/620/720 HS — the part you replace when the screen is cracked, black, shows lines, or has dead pixels after the camera took a fall, while the rest of the camera still works fine.

Camera Screen Replacement: What the DIY Repair Involves

1. Before Opening the Camera: Rule Out Simpler Fixes

A black screen does not always mean a failed LCD. Test the camera with the battery fully charged and try pressing the DISP (display) button — many Canon PowerShot models cycle through display modes including an "off" mode where the screen is intentionally blank (EVF-only, though the SX series does not have an EVF). Connect the camera to a TV via the HDMI output — if the image appears on the TV but not on the camera screen, the LCD is confirmed faulty. If the camera does not output an image via HDMI either, the problem may be the image processor board, not the LCD.

2. The Ribbon Cable: Handle With Extreme Care

The LCD connects to the camera's main board via a thin, delicate flex ribbon cable with a ZIF (Zero Insertion Force) connector latch. To disconnect the old screen: use a plastic spudger to carefully flip up the latch on the connector (do not pry it or it will snap off the board), then gently pull the ribbon cable straight out. To connect the new screen: insert the ribbon cable straight into the connector with the contacts facing the correct direction (gold contacts typically face toward the board, but verify from your disassembly photos), then press the latch down evenly. A misaligned cable causes a white screen, no backlight, or vertical lines. If the latch breaks, the repair becomes exponentially more difficult — solder-repairing these tiny-pitch connectors is expert-level work.

3. Compatible vs. Original Canon Part

This is a compatible (aftermarket) replacement screen, not an original Canon service part. Compatible screens typically use the same LCD panel specifications (resolution, brightness, color gamut) as the original, but may have slightly different anti-glare coating, viewing angle performance, or backlight color temperature. For most users, the difference is negligible in day-to-day shooting. The screen is manufactured to fit the SX610/SX620/SX720 housing and uses the correct ribbon cable format. If you are a professional relying on critical color accuracy for the rear display (as opposed to the captured image file), an original Canon part would be preferred but is typically much harder to source at retail.

Key Specifications

Frequently Asked Questions

How can I be sure this screen fits my exact camera model?

Check the model number printed on the bottom or front of your camera — it must read PowerShot SX610 HS, SX620 HS, or SX720 HS. These three models share the same rear LCD panel assembly. The SX600 HS and SX700 HS are different models with different screens — verify you have one of the three listed compatible models, not a similar-sounding model. If your camera label is worn, remove the battery and look inside the battery compartment for the model number printed on a sticker. If you are still unsure, send us a photo of your camera and we can help identify it.

What tools do I need and where can I find a disassembly guide?

You will need: a set of small Phillips screwdrivers (JIS #000, #00, #0 — Japanese cameras use JIS screws, not Phillips, and a Phillips driver can strip them), a plastic spudger or guitar pick for prying the rear case apart, tweezers for ribbon cable handling, and a clean, well-lit workspace with small parts containers. Search YouTube for Canon SX610/SX620/SX720 LCD replacement or screen repair — several disassembly videos are available. The general sequence: remove battery and memory card, remove visible screws (including those under rubber grips or stickers), pry the rear case off starting from a corner, disconnect the LCD ribbon cable, remove the screen from the rear housing (it may be taped or screwed in), install the new screen in reverse order.

The new screen works but the colors look slightly different from my original — is it defective?

A slight color temperature shift (warmer or cooler white balance) between an aftermarket compatible screen and the original Canon part is normal and not a defect. LCD panels from different manufacturing batches or suppliers have minor variations in backlight LED color temperature and LCD cell color filtration. The captured photos will not be affected — the image sensor and image processing are completely independent of the rear display. If the colors are severely off (green/magenta cast, missing entire color channels), check that the ribbon cable is fully and straightly seated — a partially-connected data line can cause color channel dropout.

The screen installation went fine but now the camera will not turn on at all — what did I break?

Do not panic — this is usually a simple issue. In order of likelihood: (1) the battery was drained during the repair or was not fully seated when you tested — charge the battery and reseat it firmly; (2) a ribbon cable other than the LCD cable was accidentally dislodged while opening the case — open the camera again and check that the power switch flex cable, the lens sensor cable, and the main board interconnect cables are all seated; (3) the battery door interlock switch (a tiny microswitch that detects whether the battery door is closed) is not being pressed because the rear case is not fully snapped together — close all case clips firmly; (4) a screw was overtightened and cracked the main board — this is rare but possible. If you are stuck, use the KOEED AI Diagnostic Tool to step through troubleshooting.

koeed.com — Your Trusted PLC Supplier. Camera parts, electronic displays, and specialty components. Worldwide shipping. Quote within 24h at Moritta@KOEED.COM.