Toky TE8-RC10W Intelligent Temperature Control Meter — 100-240V AC/DC, PID + Auto-Tune

Toky · TE8 / RC10W Series · Digital PID Controller · In stock

The Toky TE8-RC10W is a compact intelligent temperature control meter from Toky’s TE8 / RC10W family of digital PID controllers, designed for panel-mount thermal regulation on the factory floor. It accepts a wide range of thermocouple and RTD inputs, runs fuzzy-logic + PID with auto-tune, and drives relay, SSR or 4-20 mA re-transmission outputs — all from a single 100-240 V AC or DC universal supply. Pair it with the KOEED multi-brand sourcing service to land a tested unit with worldwide shipping and a 24-hour quote on your desk.

Engineers at plastic-extruder, injection-mold, food-and-beverage, kiln, oven, autoclave, semiconductor, life-science and HVAC sites use the TE8-RC10W as a drop-in replacement for older analog temperature meters that have drifted out of spec. Send the full BOM to Moritta@KOEED.COM and we will reply with availability and lead time within one business day.

1. Key Technical Specifications & Overview

The TE8-RC10W is a single-loop, panel-mount digital PID controller with a 96×96 mm DIN cutout and universal 100-240 V AC / 100-240 V DC supply. It supports nine thermocouple types (J, K, R, S, B, E, T, N), Pt100 and Cu50 RTDs, plus 0-10 V, 4-20 mA and mV analog inputs. The fuzzy-logic + PID control algorithm with auto-tune adapts the loop to changing thermal loads, while built-in ramp/soak profiles handle multi-step curing and sterilization recipes.

2. Application Scenarios — Where the TE8-RC10W Fits

The TE8-RC10W is engineered for any single-loop thermal process that needs tighter control than an analog meter can deliver. The 4-20 mA re-transmission output makes it a clean fit for plants that are modernizing one loop at a time inside a wider factory automation stack that already runs Allen-Bradley, Siemens, Mitsubishi, Omron, Fanuc, Schneider, Yaskawa, Panasonic or KEYENCE controllers.

• Plastic extruder barrel and die temperature control, often next to a Allen-Bradley CompactLogix line controller.
• Injection-mold hot-runner zones where ramp/soak profiles protect sensitive tool steel.
• Food & beverage pasteurization, retort and CIP loops with PID auto-tune on start-up.
• Kiln, oven and heat-treat furnace profiling for ceramics and metallurgy.
• Pharmaceutical autoclave and incubation chambers requiring tight ±0.3 % FS accuracy.
• Semiconductor wet-bench and chamber temperature regulation alongside KEYENCE vision inspection cells.
• HVAC air-handler, chiller and cleanroom temperature trim loops in Schneider Modicon BMS nodes.
• Life-science and laboratory incubator / refrigerator stacks under Omron SYSMAC SCADA supervision.

3. Integration & Wiring Notes

The TE8-RC10W drops into a standard 1/4 DIN cutout and exposes its terminals on the back of the bezel. Power, sensor and output terminals are clearly grouped, but the loop is a low-voltage signal circuit — keep thermocouple / RTD runs physically separated from any AC switching wires in the same trough to avoid induced noise on the PV reading. Use shielded, twisted-pair cable for analog inputs and ground the shield at the controller end only.

If the controller is being added next to a Yaskawa or Panasonic PLC, map the Modbus registers once and lock the parity / baud rate to the same as the rest of the cabinet. For legacy Allen-Bradley or Fanuc cells, use the 4-20 mA re-transmission output to feed the existing analog input module — no protocol translation needed. Cross-reference questions? Send the cabinet layout to our RFQ inbox.

4. Installation & Commissioning Tips

Panel cut-out is 92 × 92 mm to accept the 96 × 96 mm bezel; use the supplied metal clips to clamp the controller into panels from 1 mm to 6 mm thick. Allow at least 50 mm of clearance above and below the bezel for cooling and for routing sensor / output cables. The TE8-RC10W shares the same form factor with the TE8 family, so a swap from an existing analog meter is a cut-out-only job in most cabinets.

• Configure input type (TC / RTD / mV / 0-10 V / 4-20 mA), range, and decimal point before applying power — the PV display shows a sensor-break alarm if the wrong type is selected.
• Set the control mode to PID and run auto-tune from ambient with the heater at room temperature for a clean first-pass identification of Kp, Ti, Td.
• For ramp / soak recipes, program at least two segments in the profile menu and use the hold / run keys on the front panel; this is the same workflow used on Omron and Siemens SIMATIC panels.
• If you see a persistent 4-20 mA loop oscillation, check shielding termination and confirm the PLC-side analog input is configured for current, not voltage.
• For multi-loop control in a large furnace, daisy-chain up to 32 TE8-RC10W units on RS-485 to a single SCADA node — this is a common pattern in process control retrofits.
• Calibration check: a 0 °C ice-bath and a 100 °C boiling-water reference are sufficient for spot-checking Pt100 inputs; a Type K simulator covers most thermocouple work.

Need a quick loop check on the bench before going on-site? Open the PLC Analog Calculator to convert 4-20 mA into engineering units, or the Modbus CRC Calculator to verify register polling of the RC10W’s RS-485 link. For error code lookups across brands, the PLC Error Code Database is a free tool that complements the TE8-RC10W menu map.

5. Procurement, Warranty & Lead Time

KOEED sources the Toky TE8-RC10W as a brand-new unit, not a refurbished one. Every controller is bench-tested for input / output sanity, sensor-break alarm response, and 4-20 mA re-transmission accuracy before it ships. Pricing is RFQ-driven, so we do not post a fixed catalog number; a typical single-piece quote covers the unit, traceable QC paperwork, and worldwide shipping with DHL / FedEx / UPS as standard.

Questions before you buy? Email Moritta@KOEED.COM with your cabinet layout, sensor type, and target loop count, and KOEED will reply with a part list, lead time, and shipping options for the Toky TE8-RC10W within one business day. Visit the Contact Us page for additional channels, or go back to the KOEED home for the full Allen-Bradley, Siemens, Mitsubishi, Omron, Fanuc, Schneider, Yaskawa, Panasonic and KEYENCE catalog. Return and shipping policies are listed in the return policy and shipping policy pages.