new 10-36V to 19V 10A 190W isolated Waterproof power converter 12V/24V to 19V DC-DC

Home · Power Supplies · DC-DC Converters · 10-36V to 19V 10A

What Is the 10-36V to 19V 10A 190W Isolated Waterproof DC-DC Converter?

This 10-36V to 19V 10A 190W isolated waterproof DC-DC converter is a fully encapsulated step-down (buck) power module that accepts a wide DC input range from 10V to 36V and delivers a stable 19V DC output at up to 10 amps continuous current. The galvanic isolation between input and output means there is no direct electrical connection between the source and load sides — a critical safety feature for automotive, marine, and industrial applications where ground loop noise or potential differences between battery banks can corrupt sensitive electronics. The fully potted, waterproof enclosure (typically rated IP67 or IP68) allows field installation in exposed locations: under-vehicle chassis rails, engine bays, outdoor equipment enclosures, and marine bilge compartments.

In short: If you need to convert 12V or 24V battery/vehicle power to a clean, isolated 19V rail for laptops, monitors, or industrial controllers — this sealed converter does it reliably. In stock at koeed.com.

Technical Specifications

Always verify input polarity before connecting. This converter requires proper heatsinking at full load — the aluminum baseplate must be mounted to a thermally conductive surface or adequate airflow provided. Input and output wiring gauge must be sized for 10A continuous current: 12 AWG (2.5 mm²) minimum recommended.

Real-World Deployment Scenarios

• Vehicle-Mounted Computing: Power a 19V laptop, mini-PC, or touchscreen HMI from a 12V or 24V vehicle electrical system with isolation against alternator noise and load-dump surges
• Marine Electronics Bus: Derive a clean 19V rail for navigation displays or communication equipment from a 24V ship battery bank while breaking galvanic corrosion paths
• Solar-Powered Remote Stations: Convert fluctuating 12V/24V solar battery voltage to a regulated 19V for monitoring cameras, telemetry radios, or Siemens RTU equipment
• Industrial Sensor Networks: Provide isolated auxiliary power to field-mounted sensors and transmitters from a 24V control panel DC bus
• Outdoor LED Signage: Step down 24V DC to 19V for display panels in weather-exposed roadside or rooftop installations

Frequently Asked Questions

Can I connect this directly to my car's 12V battery?

Yes, but with an important caveat: automotive electrical systems experience voltage spikes during engine cranking (down to 8V) and load-dump surges (up to 40V+). Install a transient voltage suppressor (TVS diode) and a 10A fuse on the input side for protection. The converter's 10-36V input range covers normal 12V and 24V vehicle operation, but extended cranking below 10V may cause output dropout. For critical vehicle installations, consider adding an input boost pre-regulator or battery buffer.

What's the practical difference between isolated and non-isolated converters?

In a non-isolated converter, the input ground and output ground share a common electrical path. This means noise on the input line can couple directly to your load, and a short circuit on one side can propagate to the other. An isolated converter like this one uses a transformer to magnetically couple energy across a physical gap — there is no copper path between input and output. This breaks ground loops, prevents conducted EMI from reaching your load, and provides a level of safety isolation. For industrial sensor circuits, medical devices, and marine applications, isolation is essential to prevent ground-potential differences from causing measurement errors or galvanic corrosion.

Will this run my 19V laptop directly without a battery?

Yes, provided the laptop's power adapter is rated 19V and draws less than 10A. Most standard laptops draw 3-5A, well within this converter's capacity. You will need to fabricate or purchase a compatible DC barrel plug for your laptop model and observe correct polarity. The regulated 19V output closely matches the voltage of most laptop AC adapter bricks, so the laptop's internal charging circuit should accept the input without issues. However, some laptops use a center-pin ID protocol (Dell, HP) that requires a specific resistor or one-wire communication to enable charging — in those cases, the laptop may display a "power adapter not recognized" warning.

How hot does this converter get under full load?

At 190W output with >90% efficiency, the converter dissipates roughly 15-20W of heat. The fully potted aluminum baseplate must be bolted to a metal surface or heatsink for adequate thermal management. Without heatsinking, internal temperature will rise and the unit may enter thermal shutdown protection. For continuous 10A operation, mount the baseplate to a heatsink with a thermal resistance of 2 degrees C/W or better, or ensure forced-air cooling of at least 1 m/s across the enclosure.

Can I parallel two of these converters for 20A output?

Direct paralleling is not recommended unless the converter explicitly supports current-sharing. Because the output voltage regulation setpoints will differ slightly between units, one converter will carry most of the load while the other idles. For higher current, use a single higher-rated converter or implement active load sharing with external OR-ing diodes and a current-balance controller. Contact our team for alternative power solutions from Omron and Schneider industrial power supply ranges.

Copyright © 2024 koeed.com. All rights reserved. Product images and specifications are for reference; actual product appearance may vary. All trademarks are property of their respective owners.